Sportster QuikTurn 27° Steering Kit ©

xrx steering kit 20 xrx steering kit 21

Because the bearing pockets of the QuickTurn 27° kit sit above and below the steering head (above photos) we had issues with the steering stop. We’ve developed a small weld-on piece that does the job. We tried but couldn’t make a bolt-on piece to do the job with sufficient strength. My goal has always been ‘simple’ but not in this case. Flat trackers are used to this kind of fabrication so I’m not introducing the unobtainable.

xrx steering kit 22 xrx steering kit 23 xrx steering kit 24

You start by positioning the piece below the frame steering stop. Clamp it in position when you’ve established equal clearance on both sides of the tank. Then tack weld. Before you finish welding you may want to grind a little more off the right side if you are a slider and need more counter steering space. Remember in a crash that impacts the front end, the forks flex and smash into your tank so don’t make the space too narrow.

xrx steering kit 25Where are we now timing wise? I’ve just received my first batch of installation guides. These are vital to align the kit in the steering head. Improper alignment could cause horrible things to happen to your body and head at speed. I don’t know when kit will be ready to sell but we’re getting’ close.

Sportster 27° steering kit

This is a dated drawing. I will be revising it soon.

It’s time I told you what I don’t know about this steering kit.

The developing engineer has passed his drawings on to my machining company. That company will be slow in manufacturing the parts because they’ve been blasted by the military to make bomb parts (not bad thing). The last two parts are just being finalized. They are 1) an installation guide and 2) a steering stop add-on piece.

John Metz, a dirt track friend and expert, has watched stock Sportsters race and reports the front end shows a wallowing handling characteristic. Vance Deemer (Gilroy CA) says stock forks handle in a very uncertain and untrustworthy way. Comments like these tell me my kit will work wonders but the stock 

xrx steering kit 10

forks are an addition problem area. In short-stock Sportster forks internals are poor for racing. I have contacted Davey Durelle (AMA Grand National number) who is a dirt track suspension specialist. I’m sending him my forks so he can revise the valving for racing and lengthening the travel because my kit (by the way it’s made) has reduced the travel somewhat.

My goal is to include fork improvements along with my steering kit. For these reasons I can’t give you a price at this point. My goal is to supply you with a front end that works. I believe this kit will be the most important thing you can do to your racing Sportster other than equipping your bike with 19” racing tires.

I hope to be sending you updates very soon because I will be more able to do this and several of you want this kit for upcoming races.

xrx hooligan tank 1Introducing the Gen II XRX tail for round back Sportster tanks

I have started reconfiguring the front of the XRX tail to kiss the back of big round tanks-tanks made for 883s from 1991 to 2003 and 1200s from 1999 to 2003. I also have to redesign the seat bases for the foam. Most of the pattern work will be completed the week of 9/8/17.

Phil Little’s own Hooligan build

xrx tail mounted 1

Here’s the start. An 1988 with a claimed 26,xxx miles but the title said “Odometer Status Exempt.” I don’t know what that means but it’s probably not good. Rear tires were showing cords so it’s done its share of burn outs. Hope the rings aren’t toast. Notice the skeleton bar pegs-is that cool or NOT! I’m building it as a short track racer that I’ll use on the street too. I’ll just pull the plate and unhook the front brake lever. It will never see a Hooligan track because I think a 1/8 mile track is for mad men. I’m an old slider and you can’t use that advantage on an 1/8mile. As this thing comes together I’ll shoot out reports.

XRX Hooligan Race kits finally shipping

xrx fiberglass 1

xrx fiberglass 2I am now getting parts from my supplier. I took the first tail (Pete Morris’s) and plopped it on my frame. Everything fits perfectly. This is the big tank.

xrx fiberglass 3See how slick the fit is. I just bought a 1988 Sportster with a small tank. I am keen to see if the tail fits the small tank too. I’ll let you know how that goes.

xrx fiberglass 4Here are the first three tails getting the support plates installed. 

xrx fiberglass 2This is a support plate in the tail. It is the mount for taillight and license plate. This part was the biggest hang up. My glass guy was afraid to make and install them. I told him to let me do that part to speed the process. Now things are moving along Here are the taillight assemblies that mount to the support plate.